Alloy G-30 Hastelloy G-30 N06030 2.4603 WN SO Blind flange forging disc ring

G-30 Description

Alloy G-30 is an improved version of nickel-chromium-iron-molybdenum-copper alloy G-3. With higher chromium, added cobalt and tungsten, the G-30 shows superior corrosion resistance over most other nickel and iron based alloys in commercial phosphoric acids as well as complex environments containing highly oxidizing acids. The resistance of the alloy to the formation of grain boundary precipitates in the heat-affected zone makes it suitable for use in most chemical process applications in the as-welded condition.

Chemistry Typical

Nickel: Balance
Chromium: 28.00 – 31.50
Iron: 13.00 – 17.00
Molybdenum: 4.00 – 6.00
Copper: 1.00 – 2.40
Tungsten: 1.5-4.0
Cobalt: 5.00 max
Manganese:1.50 max
Columbium + Tantalum: 0.30-1.50
Carbon: 0.03 max
Phosphorus: 0.04 max
Silicon: 0.80 max
Sulfur: 0.02 max

Physical Properties

Density:0.297 lbs/in³, 8.22 g/cm³

Mean Coefficient of Thermal Expansion: :in/in/°F (mm/m/°C):
70- 212°F (20- 100°C): 7.1 x 10^-6 (12.8)

Thermal Conductivity: BTU-in/h-ft-°F (W/m-°K):
70°F (21°C) :71(10.2)

Modulus of Elasticity: ksi (MPa)
29.3 x 10³ (202 x 10³) in tension

Melting Point (approximate): 2550°F (1399°C)

Forms

Coil – Strip, Foil, Ribbon
Wire – Profile, Round, Flat, Square

Mechanical Properties at Room Temperature

Annealed Typical
Ultimate Tensile Strength: 85 KSI min (586 MPa min)
Yield Strength: (0.2% offset) 35 KSI min (241 MPa min)
Elongation: 30% min

Tempered:
Contact Ulbrich Technical Service for additional information

Additional Properties

Corrosion Resistance
G-30 shows superior corrosion resistance in commercial phosphoric acids as well as complex environments containing highly oxidizing acids such as nitric/hydrochloric, nitric/hydrofluoric and sulfuric acids. Refer to NACE ( National Association of Corrosion Engineers) for recommendations

Finishes

#1–Hot rolled annealed and descaled. It is available in strip, foil and ribbon. It is used for applications where a smooth decorative finish is not required.
#2D–Dull finish produced by cold rolling, annealing and descaling. Used for deep drawn parts and those parts that need to retain lubricants in the forming process.
#2B–Smooth finish produced by cold rolling, annealing and descaling. A light cold rolling pass is added after anneal with polished rolls giving it a brighter finish than 2D.
#BA-Bright annealed cold rolled and bright annealed
#CBA-Course bright annealed cold rolled matte finish and bright anneal
#2-Cold Rolled
#2BA–Smooth finish produced by cold rolling and bright annealing. A light pass using highly polished rolls produces a glossy finish. A 2BA finish may be used for lightly formed applications where a glossy finish is desired in the formed part.
Polished-Various grit finish for specific polish finished requirements
*Not all finishes are available for all alloys – Contact Ulbrich Sales for more information

Wire Finishes
XC-Extra clean. Bright annealed or bright annealed and cold rolled
Grease-Ultra bright finish for decorative applications
Soap-Soap is not removed from tempered wire to act as a lubricant.
*Contact Ulbrich Wire for custom wire finishes

Cold Forming
Alloy G-30 has good ductility and may be formed by conventional methods

Heat Treatment
Alloy G30 can be hardened by cold working:

Welding
For best results refer to: SSINA’s “Welding of Stainless Steels and Other Joining Methods”

We can provide Hastelloy G30 material in the form of flange, fittings, pipes, fasteners.

Huitong Group was established in 1978. After 38 years'development and innovation,by now,Huitong Group has set up multiple subsidiary companies.Among them,Zhengzhou Huitong Pipe Fitting Co.,Ltd.,with the indepent right of import and export, is mainly engaged in exporting steel pipe and pipe fittings for Huitong Group and assisting another subsidiary company of Huitong Group:Zhengzhou Huitong Machanical Equipment Co.,Ltd., in exporting machanical equipment.

Zhengzhou Huitong Pipeline Equipment Co.,Ltd.,with the strong support of Huitong Group,and years'development and innovation, are more and more professional in technical service and can manufacure products with all kinds of material,shape and size. Especially in elbows, tee, reducer, flange and pipe cap etc., we have gained more than 20 product patent, and hundreds of technology patent. Also,we have gradually taken an ireplacable role in High-pressure,high-temperature and anti-corrosion area. With the continuous construction of engery in China,such as petrol gas,electric power,etc.,our company has become the purchasing center of whole set fittings for such projects.In 2009,a foreign trade team established,is manily engaged in oil gas and electric power projects abroad.By now, our products have been exported to Canada,Malaysia,Parkistan,UAE, Eygpt,the Middle East countries, etc.. We have passed the qualification of ISO9001:2000 and API quality certification system. High-quality products and high-class service are well received by abroad customers in this industry. The unique diversified production line can offer you one-package serive, you can pruchase all complex products from us at one time. What's more, our sufficient material stock and conventional product stock can ensure you receive satisfied product in the shortest time.

With powerful financial strength,advanced managerial concept, excellent marketing service,strict quality control system and integrated marketing team,we would like to develop together with you hand in hand. Adhering to the operation principle of "faith first and clients foremost", we always supply high quality products, complete after-sales service and favorable prices. We sincerely hope to establish long-term cooperation with you on the basis of mutual benefits, reciprocity and common development.